Fitter previous year question paper
Fitter Objective Question and Answer hindi English
Q1.Name the part marked 'x' of the file. | X से इंगित रेती के भाग का नाम बताइए![]() |
(a) Edge | एज |
(b) Heel | हील |
(c) Tang | टैंग |
(d) Shoulder | शोल्डर |
|
Q2.Which type of half lap joint is used if one part of a job meets another part at some distance from the ends? | किस प्रकार का अर्ध लैपजोड़ प्रयोग किया जाता है, जब जॉब का एक भाग सिरों के अंत से कुछ दूरी से मिलता है? |
(a) End-lap input | एंड-लैप जोड |
(b) Cross-lap joint | क्रॉस-लैपजोड़ |
(c) Middle-lap joint | मध्य-लैपजोड़ |
(d) Corner-half lap joint | कोना-अर्ध लैपजोड़ |
|
Q3.Which type of notch is used for making a metal tray with 90° bend and an inside flange? | 90° मोड़ और अंदर से निकले हए किनारे के साथ धातु ट्रै बनाने के लिए किस प्रकार के नॉच का उपयोग किया जाता है। |
(a) 'V' notch | V नॉच |
(b) Slant notch | तिरछा नॉच |
(c) Square notch | वर्गाकार नॉच |
(d) Straight notch | सीधा नॉच |
|
Q4.What is the name of the hammer? | इस हथौड़े का क्या नाम है?![]() |
(a) Claw hammer | क्लॉ हथौड़ा |
(b) Ball peen hammer | बाल पीन हथौड़ा |
(c) Cross peen hammer | क्रॉस पीन हथौड़ा |
(d) Straight peen hammer | स्ट्रेट पीन हथौड़ा |
|
Q5.What is the purpose of cross cut cold chisel? | क्रॉस कट ठंडी छेनी का क्या उद्देश्य है? |
(a) Cutting keyways | कीवेज़ काटने में |
(b) Cutting curved grooves | वक्राकार नालियाँ काटना |
(c) Squaring materials at corners | सामग्री को कोनों पर चौकोर करने में |
(d) Removing metal from large flat surface | बड़ी चौड़ी सतह से धातु निकालना |
|
Q6.Which type of curve cutting hand saw is used for internal cutting in wood? | लकड़ी की आतंरिक कटिंग के लिए किस प्रकार की वक्र कटिंग दस्ती आरी प्रयोग की जाती है? |
(a) Compass saw | कम्पास आरी |
(b) Key hole saw | की होल आरी |
(c) Coping saw | कोपिंग आरी |
(d) Fret saw | फ्रेट आरी |
|
Q7.What is the name of the stake used for sheet metal work? | शीट मेटल कार्य के लिए उपयोग होने वाले स्टेक का क्या नाम है? |
(a) quare stake | वर्गाकार स्टेक |
(b) Hatchet stake | हैचेट स्टेक |
(c) Blow-horn stake | ब्लो हॉर्न स्टेक |
(d) Bevel-edge square stake | बेवल एज वर्गाकार स्टेक |
|
Q8.What is the name of tool? | औजार का क्या नाम है?![]() |
(a) Claw hammer | क्लॉ हथौड़ा |
(b) Tack hammer | टैक्स हथौड़ा |
(c) Cross pein hammer | क्रॉस पीन हथौड़ा |
(d) Straight pein hammer | स्ट्रेट पीन हथौड़ा |
|
Q9.which causes knot defect in timbers? | लकड़ी में गाँठ दोष का क्या कारण है? |
(a) Defective storage | दोषपूर्ण भण्डारण |
(b) Uneven shrinkage | असमान सिकुड़ना |
(c) Growth of branches | शाखाओं की वृद्धि |
(d) Improper seasoning | गलत सीज़निंग |
|
Q10.Name the part of file marked as x | फ़ाइल के x के रूप में चिह्नित भाग को नाम दें। |
(a) Heel | हील |
(b) Tang | टैंग |
(c) Ferrule | फेर्रुले |
(d) File length | फ़ाइल की लंबाई |
|
Q11.What is the use of a try square? | एक ट्राई स्क्वायर का उपयोग क्या है? |
(a) To check right angle | समकोण की जाँच करने के लिए |
(b) To check acute angle | न्यून कोण की जांच करने के लिए |
(c) To check obtuse angle | अधिक कोण की जांच करने के लिए |
(d) To check straight angle | सीधा कोण की जांच करने के लिए |
|
Q12.Which marking media is poisonous? | कौन सा मार्किंग मीडिया जहरीला है? |
(a) White wash | वाइट वाश |
(b) Prussian blue | प्रशियन ब्लू |
(c) Copper sulphate | कॉपर सल्फेट |
(d) Cellulose lacquer | सेल्यूलोज लेकर |
|
Q13.Which part of universal surface gauge holds the scriber? | यूनिवर्सल सरफेस गेज का कौन सा हिस्सा स्क्राइबर को पकड़ता है? |
(a) Snug | सनग |
(b) Guide pin | गाइड पिन |
(c) Rocker arm | रोकेट आर्म |
(d) Fine adjustment screw | फाइन एडजस्टमेंट पेंच |
|
Q14.A new hacksaw blade after a few stroke, becomes loose because of? | कुछ स्ट्रोक के बाद एक नया हैकसॉ ब्लेड ढीला हो जाता, जिसकी वजह है? |
(a) tretching of blade | ब्लेड खींच जाना |
(b) wrong pitch of the blade | ब्लेड की गलत पिच |
(c) improper selection of saw sets | सॉ सेट का गलत चयन |
(d) nut thread being worn out | नट के थ्रेड का घिस जाना |
|
Q15.Why breakage of teeth occur easily while sawing of thin walled work pieces and the start of cut? | पहले कट और पतले वर्क पीस को कटते समय दांतों बहुत आसानी से क्यों टूटते है? |
(a) Hand force is too big | हाथ बल बहुत ज्यादा होता है |
(b) Cutting section is too short | कटिंग सेक्शन बहुत छोटा है |
(c) Coarse blade to be used | मोटे ब्लेड का उपयोग किया जाना है |
(d) Hand force acts only upon few teeth | हाथ का बल केवल कुछ दांतों पर काम करता है |
|
Q16.Which chisel used for squaring materials at the corners, joints? | कार्नर और जॉइंट्स पर मटेरियल को चोखोर करने के लिए किस छेनी का उपयोग किया जाता है? |
(a) Flat chisel | फ्लैट छेनी |
(b) Cross cut chisel | क्रॉस कट छेनी |
(c) Diamond point chisel | डायमंड पॉइंट छेनी |
(d) Half round nose chisels | हाफ राउंड नोज छेनी |
|
Q17.Name the part of a hammer marked as x. | x के रूप में चिह्नित हथौड़े के भाग का नाम बताए।![]() |
(a) Face | फेस |
(b) Pein | पिन पंच |
(c) Cheek | चीक |
(d) Eye hole | ऑय होल |
|
Q18.Which angle is represented by the symbols on the cutting chisel? | काटने वाले छेनी पर प्रतीक। द्वारा किस कोण का दर्शाया जाता है?![]() |
(a) Rake angle | रेक कोण |
(b) Wedge angle | वैज कोण |
(c) Cutting angle | कटिंग कोण |
(d) Clearance angle | क्लीयरेंस कोण |
|
Q19.Name the property of metal which can be drawn into wires without rupture. | धातु की उस गुण का नाम बताइए जिसमे वह बिना टूटे तार में खींचा जा सकता है। |
(a) Ductility | डक्टिलटी |
(b) Tenacity | टनैसिटी |
(c) Elasticity | इलैस्टिसिटी |
(d) Malleability | मैलीएबिलटी |
|
Q20.What is the spindle movement of one division of thimble with spindle thread of 0.5mm pitch? | थिम्ब्ले के एक डिवीज़न की स्पिंडल मूवमेंट क्या होगी जब स्पिंडल थ्रेड 0.5 मिमी पिच का है ? |
(a) 0.01 mm |
(b) 0.10 mm |
(c) 1.00mm |
(d) 10. 0mm |
|
CITS back pepar please
ReplyDelete